Because the minor diameter of the barrel is 5.56 mm and the major diameter is 5.69 mm. If the bullet were smaller than that then the propellant would blow past it. They didn't make a 'murican millimetre like they did with the imperial system.
I'm upset that a meme I tried to remake with Unicode box drawing characters lines up terribly in apps: https://lemmy.ca/post/28490027 Shouldn't code blocks render in monospace?
On Lemmy's web frontend it's perfect:
On Connect it looks like this:
On Jerboa it's basically the same:
Eternity does use monospace but the box drawing characters seem to be too wide.
All I can find about it here is one post from a year ago: https://lemmy.ca/post/1492857
PSI
0 100
┣━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━┫
Dead Potentially survivable
Vs
Atm
0 100
┣━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━┫
Dead Dead
Vs
kPa
0 100
┣━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━┫
Dead Totally Fine
When in doubt - C4!
Plus it did land on the barge. Most of the debris should be there, though the remaining fuel would have mainly gone overboard. Probably the flight termination explosives also.
Your mind makes it real.
Why not an inflatable airlock? It worked* for Voskhod.
*
*I mean it didn't kill the crew...
I don't think that's what 'market share' is trying to represent, but without any context - yeah. You can lump in android phones and set-top boxes and signage and industrial controllers while you're at it.
Is OP adding the Android share to Linux? That would certainly do it.
Only makes sense if you know their definition of 'Linux' though.
I think what you want is in Firefox nightly right now: https://blog.nightly.mozilla.org/2024/08/07/firefox-sidebar-and-vertical-tabs-try-them-out-in-nightly-firefox-labs-131/
That expands and compacts based on the sidebar state and can be flipped to the right side of the window in the 'customise sidebar' settings.
cross-posted from: https://feddit.uk/post/12276336
Sorry for the crap photos - I just wanted to share these extra keys I added to my Lily58.
I noticed there was a gap in the matrix so I tacked a spare hot-swap socket to the pads on the back of the PCB. That worked with minimal modification to my QMK set-up. I couldn't really use it dangling off some wires so I set out to make an extension that would slot in and be retained by one of the standoffs. I don't have a laser cutter or 3D printer so I just hacked these out of a sheet of ABS plastic following a printed template and glued them up. They're nice and solid and line up really well, despite being rather rough around some of the edges.
I'm finding the 1.5U keys a bit confusing at the moment, swapping them out for 1U keys makes it a bit easier to home my thumbs. These are certainly much easier to access than the outermost keys on the lower row or the keys below the display. I'm thinking they need to be called Lily Pads.
Sorry for the crap photos - I just wanted to share these extra keys I added to my Lily58.
I noticed there was a gap in the matrix so I tacked a spare hot-swap socket to the pads on the back of the PCB. That worked with minimal modification to my QMK set-up. I couldn't really use it dangling off some wires so I set out to make an extension that would slot in and be retained by one of the standoffs. I don't have a laser cutter or 3D printer so I just hacked these out of a sheet of ABS plastic following a printed template and glued them up. They're nice and solid and line up really well, despite being rather rough around some of the edges.
I'm finding the 1.5U keys a bit confusing at the moment, swapping them out for 1U keys makes it a bit easier to home my thumbs. These are certainly much easier to access than the outermost keys on the lower row or the keys below the display. I'm thinking they need to be called Lily Pads.
... for you.