SpicyAnt

What if houses just lazy?

La lechuga del diablo.

Mr Beast went through four controversies in a short amount of time:

In response to both of these, Mr. Beast cut Ava out of Mr. Beast.

(3) There is a "Beast Games" show being produced by Mr. Beast for Amazon Prime. It turns out that putting 2,000 people to compete for 5 million dollars in Las Vegas was a recipe for organizational disaster. People had issues getting their medicines and underwear. People were fed low-calorie meals like a small amount of cold oatmeal and an egg spread at irregular intervals. Some people had seizures and the local hospital reported several injured visitors from the games. It was reported that the team invited people of all ages and then made them compete in physical games for which young men had a very significant advantage over the old players that were also cast. You can see an article about this here, and in the comments you can see many players sharing their bad experiences: https://www.casino.org/vitalvegas/mrbeast-shoots-beast-games-in-las-vegas/

(4) A person who has an employee for a short amount of time released a video in which he claimed a lot of Mr. Beast videos are faked/rigged. He also mentions multiple examples in which Mr. Beast broke lottery laws.

The IP is dynamic, but for my self-hosted services that require a static IP I make use of a WireGuard tunnel between my raspberry pi and a virtual private server. The VPS has a static IP, so my domains point at the VPS and then the VPS re-routes the packets via the wireguard tunnel. In a wire guard tunnel only the server needs a static IP, so the VPS can route packets to the client even if the client's ip is dynamic.

Also in the Netherlands and I have recently extended this concept to my home internet. Since 25 Mbps download / 10 Mbps upload is enough for my use, I no longer have an internet subscription and I make use of $25 LycaMobile unlimited data sim cards for home internet using a sim router. The IMEI of the router can be easily modified, which is also a plus.

Sounds exhausting 😅

I would think that that this is generally true when we zoom into a local economy. But is this true when we consider a global scale? If we were distribute the world's wealth to people in proportion to the value generated by their labor, what would the spread be like?

Does a worker in the US or a wealthy EU country receive less than the economic value/profit that they produce when we spread value fairly across the international supply chain? I suspect that workers in rich countries are able to receive more than their "fair share" for their labor by benefiting from their country's exploitation of resources and labor in poorer nations.

I am not stating this as fact. It is what I suspect, but I don't know the numbers, and I am curious to learn what others think.

I have a habbit of searching my own name a few times a week and sorting by new, to check if my name appears somewhere. It makes sense to me, but I would be self-conscious about it if someone asked me why tf I am looking myself up so often as if I'm famous

Yeah, it is written funny. But what it means is that the Linux kernel already comes pre-packaged with the drivers necessary to communicate using the protocol used by this device (UART or USB). These Linux drivers (and by extension Raspbian) are natively capable of interfacing via the GPIO pins or via the USB connectors. It is not true that the device is "driver free" as you always need a driver for this, what they meant is that it is not necessary to install any additional drivers for Linux. So "free from installation" I suppose.

Windows does not come pre-packaged with these drivers, so you need to install them if you want to interface with the device via USB. The chip that the board uses for the UART -> USB conversion is the CP2102. This chip is a common chip used in some ESP32 boards, and I think it would work fine with the standard CP210x driver. But on their site they do provide a specific driver for free (SIMCOM_Windows_USB_Drivers_V1.0.2.exe)

The board finally arrived and it is indeed the SIM7600G-H, which is the global version.

I tried it on my raspberry pi 5 and struggled a bit because there was a change to the UART interface between the PI 4 and PI 5 and the documentation on this board describes the PI 4. But, after some fiddling around I figured out the correct setting and got it to work. The main difference is that the "UART0" needs to be explicitly turned on because the default debugging UART now uses the UART10 interface that is somewhere else on the board.

You are in the perfect position to help your brothers out!

This makes me think of those who design the US immigration forms.

"Are you coming here to commit crimes?"

( ) Yes ( ) No