A "Showerthought" is a simple term used to describe the thoughts that pop into your head while you're doing everyday things like taking a shower, driving, or just daydreaming. A showerthought should offer a unique perspective on an ordinary part of life.
Modern night lights won't have this happen, as they have a built-in "buffer" to prevent rapid on/off cycles like that.
But I do remember having an old night light when I was younger, probably from the late 80s, that you could make flicker by putting your hand in front of the bulb so that the light reflects back onto the sensor, effectively turning it into a very fast Useless Machine.
Constant voltage LEDs use something called Pulse Width Modulation, or PWM, to simulate dimmed lights. That's basically what you're describing.
I knew that dimmable LEDs exist now, but I didn't know why they worked. Cool!
Like some motors they operate best at a certain duty cycle.
The issue with some really cheap ones is that it’s obvious.
It’s also why, if you’re so inclined at Christmas time, led string lights on trees are hard to photograph since you’ll catch some of them on while others are off at the time of the photo.
Duty cycle does not refer to the frequency of the flicker.
The frequency on a PWM light doesn't change, it's the same for the full range of control. What that frequency is, is determined by the controller generating the PWM signal, not the light.
PWM can be done at different frequencies. Cheap PWM controllers can only manage lower frequencies, those are the kind you notice and have trouble with in pictures. Good ones will run at frequencies so high, the fact they aren't actually on continuously, will only matter in extremely high speed photography.
This is because a PWM controller can achieve the same reduction in brightness at any frequency. What matters is the fraction of time that the LED is lit each pulse. If you run the system at 1000Hz, half brightness means the flicker is 1000Hz, because you are sending 1000 pulses that are 0.5 milliseconds long. 75% brightness would mean the pulses are 0.75 milliseconds, but the number of pulses, and thus the frequency, is still 1000Hz. The flicker is the same.
Even at 99% brightness/duty cycle, a PWM light is still blinking at whatever frequency the controller is running at. Only at 100% does it not flicker, as 100% duty cycle means the controller simply keeps the light on continuously.
No matter what LED you use, they don't usually care what the frequency is, nor what duty cycle you are at.
I'm not sure what you mean by motors running best at a given duty cycle, either. Sure, there is an efficiency peak, but the whole point of PWM is to be able to run something at any duty cycle you desire (resulting in the desired brightness for lights, RPMs for motors).
Thanks for clarifying. You’re right. It’s the duty cycle of the driver of the LED right?
And as for the motor analogy it is optimal efficiency which I thought did apply to led lifetime vs brightness output but I’m always open to be corrected.
Thanks for taking the time to break it all down for me.
Heat does affect diode lifetime. So brightness/duty cycle certainly does affect how long it'll last, because more energy going through means higher temperatures.
But with any light/fixture that has sane heat dissipation, it's not worth worrying about. LEDs will last decades in most scenarios.
I hate the flickering Christmas lights. They give me headaches.
That's how all ac powered lights work because the current is constantly alternating.
I was going to protest this, but then I started looking into how ac is converted to dc and realized that it would be cheaper to just let the diodes run on ac.
oh shit, my stoned ass wasn't prepared for this
Indeed, older bulbs work in both directions and the voltage fluctuation isn't visible in the light emitted, because the thermal mass of the filament smooths out the alternating current into a continuous glow.
But LEDs will flicker unless the AC is rectified and smoothed out. Cheap lights will just not come with the circuitry to do this, as you can just hook up the diode directly, the only drawback being it will only emit light some of time. 60Hz is slow enough that you will notice it, however. Especially with movement, it makes reality look like it's running at 60fps.
Even when rectified, unless a capacitor is added to the circuit, LEDs will flicker. AC merely rectified will still have the voltage hitting zero 60 times a second, otherwise.
Bro juat reinvented pwm thats why lights can look weird when flashes are close to a factor of the framerate.
ok but, are you high?
You need to research how optical sensors actually work.
From this source:
A phototransistor is a type of bipolar transistor in which the base-collector junction comes into light. This results in the same behavior of a photodiode
I'm high and I just wanted to post something low effort that I thought was funny. I know it's more complex than the way I described it.
Edit: also, diodes are directional. Saying that a photodiode is "a diode wired in reverse" should be the first sign that I know more than what I'm actually saying. All diodes are capable of reacting to light, a photodiode exploits and amplifies the principle.
Now take an LED light that has the exact opposite frequency to your local power grid and hold it onto the sensor. The night light won't know what hit it!