40
Question about printing times (www.thingiverse.com)
submitted 3 weeks ago by skotimusj@lemmy.world to c/3dprinting@lemmy.world
19 comments fedilink hide all child comments

Hello all. I am very new to this but it is all very cool to me. I ran into a problem and I am not sure how to troubleshoot it. I downloaded a simple pull string helicopter off thingiverse. After running through the slicer software, the estimated build time is 131 hours. Relative to it’s size this seems insane. If I “run the simulated build”, there are long holds on one of the interior walls. I am hesitant to just “try it” and see if the pauses are a software thing that does not translate to the hardware. I am not sure how to break it down from here. Any advice?

Link to the plans included

top 19 comments
sorted by: hot top controversial new old
[-] paddington@lemmy.world 13 points 3 weeks ago

You definitely don't need a layer height that low for something like this. Even still, you've got something set up weird because at a normal 0.2mm layer height it's showing just under 4 hours to print everything but the pull rods (only because I'm too lazy to split the STL apart right now.) Try resetting your build settings or start a 'new' project.

[-] skotimusj@lemmy.world 1 points 3 weeks ago

When I switch to 0.2mm the time goes to 83 hours, so I assume there is still some error. What slicer do you use?

[-] paddington@lemmy.world 11 points 3 weeks ago

Don't use Creality Slicer, it's just an outdated renamed version of Cura. Download the most recent version of Cura here and your problems will most likely go away. https://ultimaker.com/software/ultimaker-cura/

[-] skotimusj@lemmy.world 12 points 3 weeks ago

As you said. I tried this and it fixed everything. Thank you

[-] skotimusj@lemmy.world 4 points 3 weeks ago

Thanks. Will try this.

[-] Creat@discuss.tchncs.de 11 points 3 weeks ago

Can you give us your basic info:

  • Which printer
  • Which slicer
  • What kind of profile
  • Which preset (if any)
  • What filament is selecte
  • did you change any settings

and just posta screenshot of the sliced model that the slicer should show you, makes it much easier to recognize trivial errors like wrong orientation.

[-] skotimusj@lemmy.world 5 points 3 weeks ago

Here is what I remember.

Creality ender 5 s1 Creality slicer High detail profile (Infill % 15, speed 100, nozzle temp 205, bed temp 60, z axis 0.1) PLA These were the default with no changes.

I am not sure what other parameters can be changed.

I will post a screenshot tonight. I did notice that 99% of the time is on the outer wall, this is where I noticed the pauses when I simulate the print.

[-] Creat@discuss.tchncs.de 2 points 3 weeks ago* (last edited 3 weeks ago)

I'm sure the official slicer will have a good profile, maybe the speed for outer walls accidentally got changed to 1 mm/s? I don't usually use Cura (that is what their slicer is based on), but I think to change speeds at all you need to hit "show advanced" or something? So if you didn't change anything, that is even less likely.

If it's real pauses (print head stops completely), I have even less ideas what that could be.

When I get back home I can try to see what I get with your settings, probably just resetting everything should also work for you though.

[-] IMALlama@lemmy.world 8 points 3 weeks ago

I suspect what's getting you is minimum layer time. In a nutshell, extruding very hot plastic onto a layer that was very recently extruded can result in a runny mess. Minimum layer time is intended to address this.

That said 131 hours seems a bit intense.

What's your layer height? How good is your cooling? If you crank your fan, you might be able to decrease minimum layer time.

[-] Excrubulent 7 points 3 weeks ago* (last edited 3 weeks ago)

Just to add on to this, if OP is printing this standing then it really should be laid on iits side, so that the hole in the handle is facing up & down, not sideways. Looking at this print that's definitely how it should be printed. Vertical not only runs into layer time issues, but it's a tall, thin object with loads of layer seams in the middle. It will be extremely weak. Lying down the layers run along the length of it, making it stronger. If the hole is sideways, then one side of the handle makes a giant bridge, which could fail the print entirely or need lots of supports.

I imagine the designer very intentionally made it to print on its side.

Oh and put the embossed arrow facing up, assuming the other side is flat.

[-] skotimusj@lemmy.world 4 points 3 weeks ago

Layer height is 0.1mm. it's odd, because it happens on specific curved areas. There are no pauses on other areas that were recently printed.

[-] Creat@discuss.tchncs.de 5 points 3 weeks ago

A good rule of thumb is to just always use 0.2mm layers unless you have a very good reason not to.

That being said, this doesn't explain your truly nonsensical time prediction. It would just be double, since you have twice the layers to print. Like someone said, a few hours would be reasonable, certainly less than a day even with very fine detail.

[-] IMALlama@lemmy.world 2 points 3 weeks ago

You mean travel speed is slower in those curved areas? Perhaps it's due to an overhang.

Are you slicing the parts flat or are they standing up?

[-] skotimusj@lemmy.world 2 points 3 weeks ago

They are flat

[-] lal309@lemmy.world 6 points 3 weeks ago

Something else to check is your infill percentage. Make sure you don’t have it at 100% (unless you absolutely need to build something completely solid). Another thing to check is your print speed. Too low and it will take a decade to print something simple. Too fast and it cause your print to fail. At this point we will all be throwing spaghetti against the wall. Can you share a screenshot of your settings?

[-] SwearingRobin@lemmy.world 5 points 3 weeks ago

Perry the helicopter?!

[-] Sphks@lemmy.dbzer0.com 5 points 3 weeks ago

Every time I see this contraption, I can't stop to think about Gardena making propellers. Due to the chosen colors.

[-] Obi@sopuli.xyz 3 points 3 weeks ago

I'm literally looking at my garden hose roller thing and yep, can confirm.

[-] Oha@lemmy.ohaa.xyz 4 points 3 weeks ago

130 hours?!!
Somethings very wrong with your slicer

this post was submitted on 06 May 2024
40 points (95.5% liked)

3DPrinting

14578 readers
62 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: !functionalprint@kbin.social or !functionalprint@fedia.io

There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml

Rules

If you need an easy way to host pictures, https://catbox.moe may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)

Moderation policy: Light, mostly invisible

founded 1 year ago
MODERATORS
j4k3@lemmy.world
andypiper@lemmy.world
henry_rowengartner@lemmy.world
GrayBackgroundMusic@lemm.ee