this post was submitted on 08 Jul 2023
13 points (88.2% liked)

3DPrinting

15625 readers
426 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: !functionalprint@kbin.social or !functionalprint@fedia.io

There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml

Rules

If you need an easy way to host pictures, https://catbox.moe/ may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)

Moderation policy: Light, mostly invisible

founded 1 year ago
MODERATORS
j4k3@lemmy.world
andypiper@lemmy.world
henry_rowengartner@lemmy.world
GrayBackgroundMusic@lemm.ee
13
Help/suggstions for printing wood (lemmy.world)
submitted 1 year ago by Erasmus@lemmy.world to c/3dprinting@lemmy.world
7 comments fedilink hide all child comments
 

So am looking for some suggestions to try. I am printing on an Ender 3 with a MS direct drive setup.

I am using Amolen wood filament and switched the nozzle to a .8

I did test prints for everything I could think: retraction, speed, temperature, etc and picked the ones that looked the smoothest of each.

I did the PID tuning as well on the nozzle.

However, I have never printed with a nozzle this size. I tried with this filament and .4 and got non stop clogging. Some reading online lead me to think that maybe it needed to be larger since it seemed to flow so easily.

Well I got it flowing great but the tops or where the layers change look a litttle rough as you can see. I don’t know if this is something I missed in my settings or if this is due to the size of the nozzle and wanted to get some input.

The sidewalks are perfectly smooth - if that makes any difference.

top 7 comments
sorted by: hot top controversial new old
[–] Draupnir@lemmy.world 1 points 1 year ago (1 children)

Layer lines printing this direction can be troublesome… try printing vertical? Or diagonal since the layer lines will show up better. Or do the plaque behind it printing as you are flat on Z-axis and print the detailed parts separate as vertical y-axis and then use wood glue to glue them on

[–] Erasmus@lemmy.world 1 points 1 year ago (1 children)

Seems like I have ran into those before but never this bad.

I can turn it slightly as suggested but next question:

I have never gone to a larger print nozzle. I assume a loss of detail and some other issues to be expected. Is that why I am seeing this so much worse? It really seems extreme.

[–] SzethFriendOfNimi@lemmy.world 2 points 1 year ago (1 children)

It can be but if you’re using a slicer with Arachne can do a great job printing smaller extrusions than your nozzle size.

https://youtu.be/WgXM2zPusXo

[–] Erasmus@lemmy.world 2 points 1 year ago (1 children)

That’s very interesting. I have always used Cura but will try downloading Prusa and activate that - then reprint this later.

Thanks for the link!

[–] Commod0re@startrek.website 1 points 1 year ago

tbh if you printed in plain PLA you would probably see the same flaws. I don’t think you missed anything in particular. You might be able to clean up the “stalactites” (for lack of a better word) by tweaking retraction but otherwise this is pretty much just what you get when you print with details on the top layers, especially with a big nozzle

Try arachne perimeter generator Try a smaller nozzle - 0.8 is pretty big and the size of this orifice is your primary limiting factor on X/Y detail. You should be able to print wood down to at least 0.4 Try a finer layer height (may need to use a smaller nozzle to make this work)

Honestly the print looks quite clean overall, this is kinda just what you get when you print with details on the top layer. Your best bet might be to change the orientation of the part to put more of the detail along the Z axis

[–] Protegee9850@lemmy.world 1 points 1 year ago

Can you sand down the layer lines on that flat plane?