Heidegger, Heidegger was a boozy beggar who could think you under the table.
It's a fun little game!
Got the part in but my wife went into labor. We had a 8 lb 7 oz baby!
Obviously this is going to delay the progress of this saw project.
I did want to mention that the bent washer isn't very "bent". I'm going to figure out how to provide measurements once I can get to focus on this again.
I promise I'll get y'all updates at some point.
How did this turn out??
Still waiting on the part.
USPS says it should be here tomorrow (05/10/2024).
I'm looking forward to using this thing for so many projects.
Still waiting on the part. USPS is late with the shipment.
I won't let you down. I'll keep ya posted. Thanks again for all the help!
I am reluctantly ordering a single wave washer here for $9.76 if you include shipping:
5140032-75 Washer, Curved, 10.1 X 17Mm - Dewalt®
I checked all of my local hardware stores. I think Lowes usually has these, but they said their small parts vendor hasn't come to restock anything in a long time and they weren't sure when they would be coming back. All other hardware stores in my area didn't have them or staff wasn't very helpful.
I will keep everyone updated. I hope this is the last part that I need to order online. I'll try to do a summary video when I'm done because I haven't found many that really get into this level of detail on repairing this specific issue online. I'm just glad I'm keeping this thing out of the dump and I hope to start using it soon so I can start to build and repair some stuff around the house. Super excited about building a French Cleat system in my shed.
I'm looking at this part of the diagram
I'm noticing part 83 (Washer 5140032-75)
That washer appears to be bent on purpose on the linked website for replacement parts and I'm guessing that it would keep the tension on the threaded dowel consistent. I think mine is missing or it was flattened out when someone torqued the mechanism.
Upon further research that is a bowed washer, spring washer, curved washer or wave washer. Their purpose is to retain tension and it's likely the solution to my gears binding. More can be explained in this video: https://youtu.be/sG1gSQGZQl8?si=nQhzR2a8TZUwJ5rY
That's another guess.
Would like to get some guidance here.
Well, the screws were definitely over torqued, but it didn't fix the issue. I tried multiple methods to get one of the screws out but had to use a grinder and a flathead screwdriver to get it out.
I think I may have an Idea what is causing the issue after looking at the gears after your advice.
Since the clanky movement really only happens in one direction when the saw is on its side I figured it had something to do with the direction of the pressure being applied by the screw mechanism.
When I put the table saw completely upside down and then tried to move the blade up and down it was very smooth.
This led me to think that there might be some movement in the gears based on the pressure that's being applied. Watch this video to see what I'm talking about and you'll see a gap that closes when I go in one direction and opens back up in the other.
You can see the movement of the gear at about the 1:04 mark in the video.
https://youtu.be/4J7jqrm9Sn4?si=UAGNhSC3HjRo7LS8
Any advice?
Thank you!! I always appreciate learning something new.
I'm not sure where the right place to post this would be, but here goes.
I bought this DW745 Type 2 saw off of Facebook Marketplace. I think it was abused. I replaced both of the elevating shafts (5140100-04 Diagram # 82 & 5140100-05 Diagram # 84). I also had to replace both of the bevel gears (5140061-65 Diagram # 56).
The aluminum housing seems to be okay and the lifting shafts move in and out without much resistance. I'm still getting this chunky movement when I raise and lower the blade.
I'm looking for advice before I go though the whole process of replacing the entire aluminum housing (Gear Case A25607 Diagram # 213) on the motor.
I installed Gallium OS on an aging Chromebook that was no longer offered support from Google. I've been able to run FreeCAD on it with no problems.
The little Acer I bought years ago is spill proof and designed to be fixable. I think it was initially intended for kindergarten classrooms.
Initially I bought one for my dad because he was constantly getting his computer infected with viruses due to forwarding emails. This little Chromebook fixed 90% of those problems.
I loved the Chromebook so much that I bought myself too. I was disheartened when Google stop supporting the hardware but then when I found out about putting that specific version of Lennox on them it gave them new life.