this post was submitted on 07 Jan 2024
110 points (90.4% liked)

homeassistant

12008 readers
142 users here now

Home Assistant is open source home automation that puts local control and privacy first. Powered by a worldwide community of tinkerers and DIY enthusiasts. Perfect to run on a Raspberry Pi or a local server. Available for free at home-assistant.io

founded 1 year ago
MODERATORS
GreatAlbatross@feddit.uk
110
Another successful Honeywell T6 install (lemmy.ca)
submitted 10 months ago* (last edited 10 months ago) by lightrush@lemmy.ca to c/homeassistant@lemmy.world
31 comments fedilink hide all child comments
 

Here we go. The setup was pretty trivial. The setup for the Zooz GPIO Z-Wave adapter for Yellow was trivial. Adding the T6 was trivial too. I had to install 2x Z-Wave smart plugs to extend the network from where the Yellow is to where the thermostat is. I used Leviton Z-Wave smart plugs. Finally I added the automation I wanted this whole thing for. Seems to work ™

The only downside I can see so far is that the T6 doesn’t support multi-speed fan (G1/G2/G3 wiring) so I had to choose one of the speeds while wiring and I can’t use the rest. From what I can tell Ecobee seems to be able to use G1/2/3 but I’m not ready to give up on the ethernet-independent operation T6 and Z-Wave allow to have multiple fan speeds.

Does anyone know if there’s a (non-retail) variant of the T6 that supports multi-speed fan?

I needed some thermostat automation done and I stumbled upon this thread. I just attempted this and it went about as smoothly as I can imagine. If you're also in need of an offline solution, the Z-Wave version of the Honeywell T6 seems to do the job.

#homeassistant #zwave #thermostat #homeautomation

all 33 comments
sorted by: hot top controversial new old
[–] friend_of_satan@lemmy.world 47 points 10 months ago

Yo dawg, I heard you like wall plates.

[–] orion2145@lemmy.world 43 points 10 months ago (1 children)

The three layers of backplates hurts me.

[–] lightrush@lemmy.ca 19 points 10 months ago (1 children)

Gotta hide the drywall horror show the HVAC people left. 😅

[–] orion2145@lemmy.world 7 points 10 months ago (1 children)

Totally understand. I came back for mine, cleaned it all up, patched, painted and lost all back plating. But again, I totally feel your pain.

[–] lightrush@lemmy.ca 4 points 10 months ago

Some day! :D

[–] Thcdenton@lemmy.world 36 points 10 months ago (2 children)

25°. Lizard man confirmed.

[–] keefshape@lemmy.ca 10 points 10 months ago (1 children)

Right? I started sweating as soon as I saw the temp in the pic.

[–] Marsupial@quokk.au 2 points 10 months ago

Sweating over a barmy 25?

[–] Lifebandit666@feddit.uk 9 points 10 months ago (1 children)

If it's anything like my setup (posted in the thread) they'll have a colder spot in the house, whereas the thermostat is in a warm part of the house.

My Nest heats to 22 degrees C but the whole house temp is a couple degrees lower than that.

When the whole house temp hits 20 the heating is switched off, but looking at the thermostat you'd think we're heating the house to a silly temp, when in fact there's a disparity between the thermostat temp and the temp of the whole house.

[–] lightrush@lemmy.ca 4 points 10 months ago* (last edited 10 months ago)

No, it really is 25° in the two rooms this unit heats up. 🦎

With that said, the temperature rarely falls below 25°C due to the heat coming off of the neighbouring units in the building, unless I open the window. 🥹

[–] roofuskit@lemmy.world 19 points 10 months ago

You know, you don't have to use the wall plate just because it's in the box.

[–] halfwaythere@lemmy.world 9 points 10 months ago (1 children)

Too bad the damned thing is so hideous.

[–] lightrush@lemmy.ca 3 points 10 months ago* (last edited 10 months ago) (1 children)

Huh, I really like how it looks, besides the large wall plate. 😅

[–] DeltaTangoLima@reddrefuge.com 3 points 10 months ago (1 children)

Is there a particular reason you used the wall plate? Was there a larger hole to cover up?

[–] lightrush@lemmy.ca 3 points 10 months ago (2 children)

Yup. HVAC installer drywall gore.

[–] DeltaTangoLima@reddrefuge.com 1 points 10 months ago

I feel your pain. That stuff really shits me.

[–] Trollception@lemmy.world 1 points 10 months ago (1 children)

Patching drywall isn't really that bad. It's pretty bad with those plates. Watch some YouTube videos and learn.

[–] lightrush@lemmy.ca 2 points 10 months ago* (last edited 10 months ago) (1 children)

Can patch but it'll be 1-2 days of work for a good painted finish. Would have to do multiple patching/sanding coats, masking, priming then a couple of rolls of paint of the wall. It's not trivial amount of work. For a slap-dash finish I could skip some of the steps but then again for a slap-dash look I can keep the wall plates. 😅

[–] ripcord@lemmy.world 2 points 10 months ago

And it really doesn't look that bad, in the scheme of things.

[–] Omacitin@lemmy.world 5 points 10 months ago

I've got a T6 Z-Wave also, controlling a 2-stage heat pump. I have it connected to HA through Zwave2mqtt. It's been pretty great except for two things:

A. Changing the time has no effect, as if the clock is read-only due to a hardware issue. I've had to set up the daily schedule in HA instead, but it's probably better that way anyway.

B. I can't see the stage and aux heat status in HA. Looks like all it exposes is a 'heating' or 'cooling' state. Anybody know how to get more info?

[–] killeronthecorner@lemmy.world 4 points 10 months ago* (last edited 10 months ago) (2 children)

My setup is a bit different but I had a lot of fun putting it together. I have a D1 mini with a switch hat wired into the boiler.

The D1 runs a tiny web server that lets me turn the heating on and off. Then I have a bunch of ZigBee thermostats around the house that provide a fuzzy average temperature.

Then I have a custom dash in hass that displays pretty much what a hive would display.

Whole setup cost about $20 and has been running nonstop for over 5 years!

[–] Lifebandit666@feddit.uk 2 points 10 months ago

Mine is also different.

I got a Google Nest E thermostat off eBay from a charity shop for £12 and wired it in to where my old dumb dial thermostat was.

My ZigBee thermostats are just my ZigBee motion and door sensors that also have a temperature element.

I turned off the Nest smarts in Nest, and had HA come up with average temperatures for the whole house using the ZigBee things, then recreates the smarts in HA.

The Nest E smarts stopped working 6 months later but the heat link still worked, so I bought another off eBay for £20 and paired that.

I am gonna just get some ZigBee temp sensors at some point, but this works well enough for now.

[–] lightrush@lemmy.ca 1 points 10 months ago (1 children)

Yeah, I suppose one could do a generic thermostat in HA and use just a few smart switches. However that requires some rewiring of the previously thermostat-controlled device.

[–] killeronthecorner@lemmy.world 2 points 10 months ago* (last edited 10 months ago)

In my previous house, the v1 prototype was wired straight to the boiler as there was no previous thermostat. In the current house, the v2 is wired to the Honeywell, so one can override the other as they are in parallel.

It was pretty finnicky stuff and I had to scour the internet for decade old wiring guides, but I like that sort of thing so it was good fun.

Every solution is a good solution if it makes your life easy and you have fun installing it!

[–] sue_her_birds@sh.itjust.works 3 points 10 months ago

I like this thermostat except for one issue. When i manually change the target temperature with the HA thermostat card, it has a maximum temperature of 40 degrees. With Fahrenheit, this is obviously no good. it has something to do with the MQTT configuration but i cant figure it out. Luckily service calls in automations work fine.

[–] Osiris@lemmy.world 3 points 10 months ago* (last edited 10 months ago) (1 children)

Hey I got one too! I took it apart and repainted it black to match.
For temp schedules I made a local calendar in HA with repeating events with a description of "high" "mid" and "low". The automation trigger is a calender event that reads the description and sets the temp accordingly

[–] Omacitin@lemmy.world 1 points 10 months ago (1 children)

FYI, there is a Scheduler card that might make that automation easier.

https://github.com/nielsfaber/scheduler-card

[–] Osiris@lemmy.world 1 points 10 months ago

That looks way easier than what I got going on. I'll check it out.

[–] overzeetop@lemmy.world 2 points 10 months ago

I wish I could figure out the code to get my T6 to control the Confortotal mini split I got off eBay. I have to think they’re using some genetic code base, but I couldn’t find a matching one.