this post was submitted on 07 Dec 2023
110 points (93.7% liked)

Climate - truthful information about climate, related activism and politics.

5372 readers
734 users here now

Discussion of climate, how it is changing, activism around that, the politics, and the energy systems change we need in order to stabilize things.

As a starting point, the burning of fossil fuels, and to a lesser extent deforestation and release of methane are responsible for the warming in recent decades: Graph of temperature as observed with significant warming, and simulated without added greenhouse gases and other anthropogentic changes, which shows no significant warming

How much each change to the atmosphere has warmed the world: IPCC AR6 Figure 2 - Thee bar charts: first chart: how much each gas has warmed the world.  About 1C of total warming.  Second chart:  about 1.5C of total warming from well-mixed greenhouse gases, offset by 0.4C of cooling from aerosols and negligible influence from changes to solar output, volcanoes, and internal variability.  Third chart: about 1.25C of warming from CO2, 0.5C from methane, and a bunch more in small quantities from other gases.  About 0.5C of cooling with large error bars from SO2.

Recommended actions to cut greenhouse gas emissions in the near future:

Anti-science, inactivism, and unsupported conspiracy theories are not ok here.

founded 2 years ago
MODERATORS
you are viewing a single comment's thread
view the rest of the comments
[–] monsieur_jean@kbin.social 4 points 1 year ago (10 children)

Any Asians, specifically Chinese in here with induction stoves to give us a feedback? How does it work with thin steel woks?

[–] CadeJohnson 1 points 1 year ago (1 children)

not Chinese, but I cook a lot with a wok. I also have a single induction cooktop and surprisingly, the wok has enough iron to work with it while some old cheap conventional cookware did not. However, wok cooking needs to be hot all over the wok and not just in that little point where the wok is close enough to the induction coil.

I have a conventional propane stove which I need to keep, because here in Puerto Rico the power system is quite unreliable (especially during a bad hurricane year). But the conventional stove burners are not really hot enough. With a 1/16 - inch drill bit I could increase one of the burners capacity substantially. I painted the stove knob red so people have some warning when they light that burner! It burns more gas, but wok cooking is really fast, so in the long run it is probably more efficient than lots of other cooking approaches.

I would definitely consider a wok-shaped induction heater. Induction heating is quite remarkable.

[–] monsieur_jean@kbin.social 1 points 1 year ago (1 children)

Thanks for the feedback. That's my situation in South East Asia, power can be unreliable at time. I cook with a gas stove and have a portable electric stove as a backup if I run out of gas in the middle of my cooking.

I used to cook with a high pressure stove (the ones you see in Chinese restaurant) that are perfect for woks but my wife was afraid I would burn down the house so I switched to a regular gas stove.

Induction could be an option in the future though, if it allows for that fast heating/cooling style of cooking I use.

[–] CadeJohnson 2 points 1 year ago

In the US, stove burners are rated in the confusing units of "BTUs" which is actually a unit of energy, not power. When they say BTU, they mean BTU/hour. The highest-rated burners on a typical stove are about 10,000 Btu (per hour), but high-end stoves can get up to about 18000 - that is equivalent to about 5000 watts. My single-element induction top is only rated for about 1000 watts. So although it heats and cools rapidly, I suspect it is not up to the demands of wok cooking (unless one wants to cook only very small portions).

load more comments (8 replies)