this post was submitted on 09 Sep 2024
546 points (98.8% liked)

Not The Onion

12200 readers
438 users here now

Welcome

We're not The Onion! Not affiliated with them in any way! Not operated by them in any way! All the news here is real!

The Rules

Posts must be:

  1. Links to news stories from...
  2. ...credible sources, with...
  3. ...their original headlines, that...
  4. ...would make people who see the headline think, “That has got to be a story from The Onion, America’s Finest News Source.”

Comments must abide by the server rules for Lemmy.world and generally abstain from trollish, bigoted, or otherwise disruptive behavior that makes this community less fun for everyone.

And that’s basically it!

founded 1 year ago
MODERATORS
 
you are viewing a single comment's thread
view the rest of the comments
[–] M0oP0o@mander.xyz 13 points 1 month ago (2 children)

Possible with a semi auto, since the chamber and barrel would transmit heat better to a chambered round then the magazine and all the safety parts don't really assume cook off. Yeah a round fires, slide racks back and loads next round, next round cooks off, over and over until all rounds are the same temp.

Spooky stuff.

[–] KillingTimeItself@lemmy.dbzer0.com 3 points 1 month ago (1 children)

it's possible, but i'd also assume you would probably not have a round chambered at all, so. Although, depending on the gun, it's not held back, so you're probably not going to properly rack and engage another round into the chamber. From what i understand, most small handguns have this problem if you limpwrist them. It's less common sometimes, but i imagine if it's not being held at all, this is going to be a pretty common occurrence.

[–] M0oP0o@mander.xyz 10 points 1 month ago (1 children)

This is the same person that put a loaded firearm in the oven we both know there was a round in the chamber.

And no, in my experience very few hand guns have the "limpwrist" issue.

[–] KillingTimeItself@lemmy.dbzer0.com 3 points 1 month ago (1 children)

This is the same person that put a loaded firearm in the oven we both know there was a round in the chamber.

yeah, that's probably fair.

And no, in my experience very few hand guns have the “limpwrist” issue.

hmm, either case, this guns is im assuming just sitting in there, so if it does fire a round, the force to rack the slide would have to be less than the required force to move the gun around. It's possible it could do both, due to physics fuckery, but i've not exactly tested that one...

[–] M0oP0o@mander.xyz 2 points 1 month ago (2 children)

I really want to test this, but the idea of inventing a more random version of Russian roulette where the gun is in a box and will shoot at random in a random direction you can not see......

Damn it, I need to test this.

[–] KillingTimeItself@lemmy.dbzer0.com 2 points 1 month ago (1 children)

the gun in the box is both fired and not fired, until we look inside the box BANG OW!

[–] M0oP0o@mander.xyz 2 points 1 month ago (1 children)

Well that is on you for looking inside the box. Do you know nothing about quantum gun ovens?

[–] KillingTimeItself@lemmy.dbzer0.com 1 points 1 month ago (1 children)

tru tru, my bad, i should've left the box alone.

[–] M0oP0o@mander.xyz 1 points 1 month ago (1 children)

Yeah, just leave that particular waveform uncollapsed please

what happens if we reform it tho

[–] Crozekiel@lemmy.zip 1 points 1 month ago (1 children)

Can I recommend digging a hole to test in. In addition to the typical hide behind a very solid wall not right next to it with some way to remotely pull the trigger. And one live round with the followup round being a dummy would also be a good bet.

But there are so many variables to test here... If it works on a smooth surface then you gotta see if it works on a surface like an oven rack. Would have to check different models as well. We just really need some semiprofessional to test this thoroughly.

[–] M0oP0o@mander.xyz 2 points 1 month ago (1 children)

I would need to ether dig a whole and also have a bullet stopping roof on it or build a four berm range. I was thinking the better way to test it would be to hand load some rounds with the same powder load and bullet weight (needed to cycle the action) but with a bullet equivalent that is not capable of much penetration (like a fine lead powder).

I think I would start with 2 rounds and the firearm fixed in place (to test if the action will cycle at all). Then go to oven with gun on baking sheet and 2 rounds. Then go oven rack and 2 rounds. And then maybe baking sheet and full mag if it all worked as theorized. I don't think you need a way to pull the trigger since the firearm while heating is inherently in an unsafe condition, you would have to instead leave the thing to cool for a long time (also to rule out hang fires) and unload the rounds for inspection (not to be reused).

[–] Crozekiel@lemmy.zip 2 points 1 month ago (1 children)

Oh I was definitely just considering testing the firearm being able to cycle the action when sitting loose on a flat surface, lol. I wasn't anticipating getting a fully functioning oven in the hole, that does complicate the matter considerably.

[–] M0oP0o@mander.xyz 2 points 1 month ago

Oh if I tested this it would be full on danger oven. The most expensive part would be the ruined pistols (extra difficult in my country where we can no longer legally buy new ones)

[–] Fedizen@lemmy.world 2 points 1 month ago (1 children)

looking at the images they showed the handle looked messed up, the call also stated an explosion not multiple, suggesting all the ammo went off at once.

[–] M0oP0o@mander.xyz 1 points 1 month ago

I would assume even if a few rounds went off in the barrel once a set temp was reached they would all cook off. The mechanics of this is really interesting.