3DPrinting
3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
The r/functionalprint community is now located at: !functionalprint@kbin.social or !functionalprint@fedia.io
There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml
Rules
-
No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
-
Be respectful, especially when disagreeing. Everyone should feel welcome here.
-
No porn (NSFW prints are acceptable but must be marked NSFW)
-
No Ads / Spamming / Guerrilla Marketing
-
Do not create links to reddit
-
If you see an issue please flag it
-
No guns
-
No injury gore posts
If you need an easy way to host pictures, https://catbox.moe/ may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is 
Moderation policy: Light, mostly invisible
view the rest of the comments
What's your end game? I printed parts for my Voron on an older non-ender i3 clone. To do so I
The parts printed pretty well, but the printer started... getting flaky toward the end. I suspect it's because the electronics were still enclosed in the printer, which was then enclosed inside the cardboard. If I had to do it again, I would try to make a somewhat more complicated enclosure to keep the electronics out of it and/or relocate the electronics or add a fan to them.
Ultimately I’m printing a lot of MTG commander deck boxs with screw tops and would like them to include a seal so their water tight. I’m also starting to design some camera adapters that need to set outside for a lengthy period of time.
I got lucky with mine since neo came with an all metal hot end but haven’t done any upgrades. Long term I was pretty much just planning to use this one until it stops printing, but now this is a full blown addiction and I’m hoping to get a second printer with multiple hot ends when my wife and I get get some more space.
Thank you for the ASA tips! Do you have any recommendations on printing that material? I think I overlooked that filament.
Have you tested any of your prints to see if they're water tight? That's not an easy feat, but figuring it out also won't require an enclosure. I once tried printing a pool part out of PETG and it filled with water very quickly - you could see it whicking through the layer lines. Once you nail water tight printing via tuning, a TPU gasket should give you a pretty decent seal.
Are you looking to go multi-matetial? I've run quite a range of material through my stock i3 extruder and also my Rapido HF on my stealthburner. Both extruders have handled a decent range of materials without a ton of fuss.
I went for ASA over ABS because it has a reputation for being lower odor and easier to print. If you've figured out PETG, ASA won't be too hard. Natural colored ASA was super easy to print. Colored ASA needed a lower extrusion multiplier and was more prone to warping in my experience. Don't rush either (do a test print, clean and level your bed, use an enclosure) and it shouldn't be that hard. Assuming I had a clean and level bed prints were pretty uneventful. I went for 100 bed / 245 extruder. The only small gotcha was needing to PID tune at the higher temperature.
Not yet, I’ve only ever printed PLA and heard that it will never get water tight. Grant it, I have a print I can test when it finishes up in a day or two.
I thought about running multi-material but would need to get that add on that can splice in filaments to run through the Neo’s single extruder ( maybe the sidewinder x1?), but can’t remember what it’s called to look at reviews
I wouldn't worry about multiple extruders in that case. Most of the current high performers are well rounded enough to be able to handle most anything you throw at them.
Thank you!